127 replies to this topic

[CartRacer56]

Hey guys! Cartracer56 here with my 2014 summer project / recreation some people know who it is so plz dont tell anybody (turtleman24, SCM, Connector1o1)

GUESS WHAT IT IS!


(Hint look at the right side)
i plan for this to take all summer so i will be building slow i will have to buy a lot more pieces to finish this!

Edited by Cartracer55D, 31 July 2014 - 11:23 AM.

[TheCodeMaster]

It's a lift hill, with chain

[CartRacer56]

if you look to the right you will have a better idea

[The Stig]

The Beast?

[CartRacer56]

^ incorrect

[Muzz135]

Scorpion? The drop sets it up for a loop in the right place?

[Jumpge]

Guys it's Deja Vu.

[Connector1o1]

I know what it is? O.O
BTW: The X-ties look very nicely spaced in this picture!

Edited by Connector1o1, 13 May 2014 - 02:34 PM.

[CartRacer56]

its not Scorpion or Deja Vu either and i revealed it on chat Connector1o1

[CartRacer56]

HINT its a woodie

[Turtle Man 24]

I consider it a hybrid.

[JayketheKid]

I consider it a hybrid.

Outlaw run recreation. Also if you consider it a hybrid I get....angry...... Lol naw that's your opinion though.

[CartRacer56]

finally someone got it yes its outlaw run

[Old_Hag]

Just a note, keep in mind that the upwards double barrel roll is going to be extremely hard to do speed wise. You're gonna have to support this really well.

[CartRacer56]

i have studied that very well and if the angle of it going up is what i think it is i should be fine speed wise and need breaks at the end!

[JayketheKid]

Also realize that outlaw run is a terrain coaster. It's not built on flat grounds the lift will have to be about half the size of the drop. And the 153 outer banked turns exit goes down a little bit turns and drops more then goes up short.
If you struggle anybit whatsoever with the layout, message me. I know way too much about outlaw run for my own good.

It's funny rigtpht before is saw your post, I was going to start a recreation also. Well I will have to after yours maybe unless you don't mind if a start one too. If soo talk to me also.

[SamIsSoAwsome]

I wish you luck. That is all.

[soggyhotdoggg]

Just keep in mind, you cancelled heart-breaker due to lack of pieces and in addition, outlaw run is a woodie (though a hybrid which seem to be weirdly supported) and will suck up your parts.
I won't stop you but I'll just point that out. Looks nice so far btw

[CartRacer56]

I WILL finish this @soggyhotdoggg i am willing to spend a thousand dollars on pieces and i know how much pieces woodies take and how much i will need at max

@jaykethekid ummmm the blueprints i found say it is relatively flat with the drop being a little lower than the drop and the high speed low float sits kinda low but i will message you if i encounter any problems

[CartRacer56]

Here is what you all have been waiting for the first real update!!!!!!!
The overview i do these at the beginning of every update (sorry for it being blurry)

am i doing the "Woodie" style right?

pre lift

the exit of the twist and turn

the valley between the twist and turn and the wave turn

the beginning of the wave turn i will most likely raise it up a granite rod

and the first half of the wave turn

I WILL MOST LIKELY RAISE EVERYTHING UP BY 1 GRANITE ROD!!!!!!!
THATS ALL FOR NOW!!!!!!!! COMMENT!!!!!!!!!
(If you want)

Edited by Cartracer55D, 14 May 2014 - 08:34 AM.